变速箱升挡缓慢是指在汽车行驶时，升挡车速明显高于标准值，升挡前发动机转速翩高，必须采用加速踏板提前升挡的操作方法(即松开加速踏板几秒后再踩下)才能使自加速无力有很多原因，常见的就是油泵油压达不到，活塞环.气门等密封不严跟火花塞跳火强度也有关系。另外再清洗一下喷油嘴。
The slow upshift of the transmission means that when the vehicle is driving, the upshift speed is significantly higher than the standard value, and the engine speed is high before upshift. The operation method of upshifting in advance of the accelerator pedal must be adopted (i.e. release the accelerator pedal for a few seconds and then press it) to make the self acceleration weak. There are many reasons. The common one is that the oil pressure of the oil pump cannot reach the standard value, and the piston ring The lax sealing of valves is also related to the spark plug spark strength. In addition, clean the fuel injection nozzle.
出现自动变速器升挡缓慢的情况，可能是换挡电磁阀出现故障导致。如果是偶发性故障，一般可以通过故障码或者升级程序来因此，若在P挡状态下行强拖动车辆，必然造成自动变速器外壳的损坏，导致重大损失;同时，在上下坡停车时，也不要仅仅使用P挡制动车辆，而应该牢牢拉紧手制.。
The slow upshift of automatic transmission may be caused by the failure of shift solenoid valve. If it is an accidental fault, it can generally be solved by eliminating the fault code or upgrading the program. Therefore, if the vehicle is forced to drag in the P gear state, it will inevitably cause damage to the automatic transmission housing and heavy losses; At the same time, when parking uphill and downhill, don't just use p gear to brake the vehicle, but firmly tighten the hand brake.
汽车提速提不起来，需要进行如下几种方法:使用汽车诊断电脑检测是否有故障码，排除故障后就能修复。自动挡提速慢油耗高，反正原因较多，油头，氧传感器，节气门，变速器，耦合器，正时，烧机油，要逐步检测才行。寿命比手动变速器低，易耗品，每隔一段时间必须保养。
The car can't speed up, so we need to carry out the following methods: use the car diagnostic computer to detect whether there are fault codes, and repair them after troubleshooting. The speed of automatic gear is slow and the fuel consumption is high. There are many reasons anyway. The oil head, oxygen sensor, throttle, transmission, coupler, timing and oil burning should be tested step by step. The service life is lower than that of manual transmission. It is a consumable and must be maintained at regular intervals.
车辆更换齿轮油后提速变慢了，这是什么原因导致的？这个很有可能是齿轮油粘度不对造成的，也就是换了不对的变速箱油。换油之前应该好好看看说明书，对车辆所使用的油水型号，粘度，等级，技术指标等等要心里有数。如果齿轮油选型不对，就会出现，冷车挂档生涩，热车后，行驶中降档不顺畅，容易出现卡齿现象，而且，怠速时候，方向盘，变速箱的抖动明显增大。
The acceleration of the vehicle slows down after changing the gear oil. What is the reason? This is probably caused by the wrong viscosity of the gear oil, that is, the wrong transmission oil is changed. Before changing the oil, you should take a good look at the instructions and know the oil-water model, viscosity, grade, technical indicators, etc. used by the vehicle. If the gear oil is not selected correctly, it will appear that the gear shift of the cold car is astringent, and after the hot car, the downshift is not smooth during driving, which is easy to get stuck. Moreover, when idling, the jitter of the steering wheel and gearbox increases significantly.
济南自动变速箱维修人员建议看看车辆说明书，查找适合本辆车用的手动变速箱油型号。如果齿轮油性能低下也会造成挂档生涩，更好用福斯的手动齿轮油。这是由于你更换的齿轮油的品质不高，导致不能给齿轮起到一个润滑的作用。换完变速箱油后因为是新油，还比较粘稠，所以变速箱换挡会稍有缓慢。过段时间就好了。
Jinan automatic transmission maintenance personnel suggest looking at the vehicle manual to find the manual transmission oil model suitable for this vehicle. If the performance of gear oil is low, it will also cause astringency in gear. It is best to use Flowserve manual gear oil. This is because the quality of the gear oil you replace is not high, so you can't lubricate the gear. After changing the transmission oil, because it is new and viscous, the transmission shift will be slightly slow. It'll be fine in a while.
如果变速箱油多了淹过行星齿轮，产生大量的气泡，气泡会在油里面，影响正常的油压。油的压力是很大的，气的压力相对要小很多，所以压力才不够用。变速箱出现故障很大的原因是阀体太脏导致的，变速箱阀体脏太脏会破坏变速箱油的质量和摩擦特性。加大摩擦和磨损，同时油泥也会在变速箱内产生，造成阀体和管路堵塞，无法顺序实现对油压的调节，从而出现变速箱故障问题。
If the transmission oil is too much, it will flood the planetary gears and produce a large number of bubbles, which will be in the oil and affect the normal oil pressure. The pressure of oil is very high, and the pressure of gas is relatively much lower, so the pressure is not enough. The main reason for the failure of the transmission is that the valve body is too dirty. The dirty valve body of the transmission will damage the quality and friction characteristics of the transmission oil. Increase friction and wear. At the same time, oil sludge will also be generated in the gearbox, resulting in the blockage of the valve body and pipeline, which can not adjust the oil pressure in sequence, resulting in the problem of gearbox failure.
The reasons for the slow shift and slow acceleration of the automobile gearbox are the above. If you have other problems to solve, you can come to our website www.jnbsx Com.
